added configs to booket, pluck and byte

booker/booker.ino

@@ -3,6 +3,7 @@
 //
 // Released under the Apache 2.0 License
 
+#include "config.h"
 
 /// BOOKER
 ///
@@ -20,7 +21,7 @@
 ///
 /// THE LESLIE.  Booker comes with a Leslie, which is on by default:
 
-#define LESLIE_ON               // To turn this off, put a // before the #define, as in //#define
+// #define LESLIE_ON               // To turn this off, put a // before the #define, as in //#define
 
 // Leslie changes both the amplitude and pitch at a certain rate.
 // You can adjust them here
@@ -336,15 +337,6 @@ int8_t drawBarAmplitudes[9] =
     };
 
 
-#define CV_POT_IN1    A7    // Note in, Pitch Scaling
-#define CV_POT_IN2    A6    // Gain
-#define CV_POT3       A4    // Organ Selection
-#define CV_IN3        A2    // [Unused]
-#define CV_AUDIO_IN   A0    // Pitch Tune
-#define CV_AUDIO_OUT  9     // Out
-#define CV_GATE_OUT   10     // [Unused]
-
-
 #define MEDIAN_OF_THREE(a,b,c) (((a) <= (b)) ? (((b) <= (c)) ? (b) : (((a) < (c)) ? (c) : (a))) : (((a) <= (c)) ? (a) : (((b) < (c)) ? (c) : (b))))
 uint16_t pitchCV;
 uint16_t tuneCV;
@@ -411,7 +403,7 @@ void setup()
             drawbars[i][j] = drawBarAmplitudes[drawbars[i][j]];
             }
         }
-    initializeFrequency(CV_POT_IN1, CV_AUDIO_IN);
+    initializeFrequency(CVIn, Knob1);
     }
 
 void loop()
@@ -430,7 +422,7 @@ uint16_t gain;          // our current gain
 uint16_t counter =0;
 void updateControl()                          
     {
-    float frequency = getFrequency(CV_POT_IN1, CV_AUDIO_IN);
+    float frequency = getFrequency(CVIn, Knob1);
         
     // leslie!
 #ifdef LESLIE_ON
@@ -445,7 +437,7 @@ void updateControl()
         }
 
     // determine the gain
-    gain = 1 + (mozziAnalogRead(CV_POT_IN2) >> 2)                       // Gain (Volume)
+    gain = 1 + (mozziAnalogRead(Knob3) >> 2)                       // Gain (Volume)
 #ifdef LESLIE_ON
 #if LESLIE_VOLUME==0
 #else
@@ -458,7 +450,7 @@ void updateControl()
     if (++counter == COUNTER_MAX)
         {
         counter = 0;
-        organ = (organ + (mozziAnalogRead(CV_POT3) * NUM_DRAWBAR_SELECTIONS)) >> 10;  // Organ Selection
+        organ = (organ + (mozziAnalogRead(Knob2) * NUM_DRAWBAR_SELECTIONS)) >> 10;  // Organ Selection
         }
     }                                             
 

booker/config.h

@@ -0,0 +1,22 @@
+//Settings
+const int pitchSubSteps = 32; //set how many steps are there between semitones. set to 1 to quantize to semitones
+const int driveAmount = 450;
+#define MOZZI_CONTROL_RATE 1024
+
+//Hardware Definitions
+#define Knob1   A6  //Pitch
+#define Knob2   A4  //Atonality
+#define Knob3   A2  
+#define Knob4   A0  
+#define KnobA   A5  //Attack
+#define KnobDR  A3  //Decay and Release
+#define KnobS   A1  //Sustain
+#define CVIn    A7  //CV input and Pitch knob
+#define GateIn  10
+#define EnvSwitch 11
+#define DroneSwitch 12
+#define LED     5
+
+#define MOZZI_ANALOG_READ_RESOLUTION 10
+
+//MIDI_CREATE_DEFAULT_INSTANCE();

byte/byte.ino

@@ -121,8 +121,6 @@
 	
 	
 
-	
-
 #define CV_POT_IN1    A7    // Note In, Pitch Scaling                   // Filter Cutoff
 #define CV_POT_IN2    A6    // Filter Cutoff
 #define CV_POT3       A4    // Resonance

pluck/config.h

@@ -0,0 +1,22 @@
+//Settings
+const int pitchSubSteps = 32; //set how many steps are there between semitones. set to 1 to quantize to semitones
+const int driveAmount = 450;
+#define MOZZI_CONTROL_RATE 1024
+
+//Hardware Definitions
+#define Knob1   A6  //Pitch
+#define Knob2   A4  //Atonality
+#define Knob3   A2  
+#define Knob4   A0  
+#define KnobA   A5  //Attack
+#define KnobDR  A3  //Decay and Release
+#define KnobS   A1  //Sustain
+#define CVIn    A7  //CV input and Pitch knob
+#define GateIn  10
+#define EnvSwitch 11
+#define DroneSwitch 12
+#define LED     5
+
+#define MOZZI_ANALOG_READ_RESOLUTION 10
+
+//MIDI_CREATE_DEFAULT_INSTANCE();

pluck/pluck.ino

@@ -1,3 +1,9 @@
+// PLUCK by Sean Luke adapted for Sitka Instruments WS-1.0 by Oleksiy Hrachov
+// TODO: 
+// - rework randomSeed because there's no proper RANDOM_PIN available
+// - add MIDI capabilities
+
+
 // Copyright 2023 Sean Luke
 // (sean@cs.gmu.edu)
 //
@@ -87,8 +93,7 @@
 ///
 /// POT 3           Gain 
 
-
+#include "config.h"
-
 
 // this is literally just a deterministic random number table, stolen from arp.ino
 PROGMEM const uint8_t NOISE[8192]  = 
@@ -661,22 +666,13 @@ uint8_t currentWave = 0;
 uint8_t wavePos[NUM_WAVES];
 uint8_t waveLength[NUM_WAVES];
 
-
-
-#define CV_POT_IN1    A7    // Note In, Pitch Scaling
-#define CV_POT_IN2    A6    // Atonality
-#define CV_POT3       A4    // Volume
-#define CV_IN3        A2
-#define CV_AUDIO_IN   A0    // Pitch Tune
-#define CV_AUDIO_OUT  9     // Out
-#define CV_GATE_OUT   10    // Trigger
 #define RANDOM_PIN    A5
 
 void setup() 
     {
     // some reasonable initial defaults
-    pinMode(CV_GATE_OUT, INPUT_PULLUP);
+    pinMode(GateIn, INPUT_PULLUP);
-    initializeFrequency(CV_POT_IN1, CV_AUDIO_IN);
+    initializeFrequency(CVIn, Knob1);
     randomSeed(RANDOM_PIN);
     startMozzi();
 
@@ -894,24 +890,24 @@ uint8_t waitCount = 0;
 inline void readPots()
 	{
 #ifdef ATONALITY_ON_POT_2        
-    atonality = ATONALITY_VAL(mozziAnalogRead(CV_POT_IN2) >> 2);
+    atonality = ATONALITY_VAL(mozziAnalogRead(Knob2) >> 2);
-	uint8_t s = mozziAnalogRead(CV_IN3) >> 7;
+	uint8_t s = mozziAnalogRead(Knob3) >> 7;
 #else
-    atonality = ATONALITY_VAL(mozziAnalogRead(CV_IN3) >> 2);
+    atonality = ATONALITY_VAL(mozziAnalogRead(Knob3) >> 2);
-	uint8_t s = mozziAnalogRead(CV_POT_IN2) >> 7;
+	uint8_t s = mozziAnalogRead(Knob2) >> 7;
 #endif
 	scale = scales[s];
 	shift = shifts[s];
-    gain = mozziAnalogRead(CV_POT3) >> 6;
+    gain = mozziAnalogRead(Knob4) >> 6;
 	}
 	
 	
 void updateControl() 
     {    		
-	uint16_t pitchPos = getPitchPos(CV_POT_IN1, CV_AUDIO_IN);		// we have to call this each time
+	uint16_t pitchPos = getPitchPos(CVIn, Knob1);		// we have to call this each time
     //readPots();
     // Check for a trigger
-    uint8_t tr = !digitalRead(CV_GATE_OUT);
+    uint8_t tr = !digitalRead(GateIn);
     if (!triggered && tr)
         {
         waitCount = 4;